Mounting Dream UL Listed TV Wall Mount for Most 26-55 Inch TVs, Full Motion TV Mount with Perfect Center Design, Articulating Wall Mount TV Bracket Swivel and Tilt, Max VESA 400x400mm, Up to 77LBS

A great all-purpose articulating mount for larger TVs
This is the third articulating arm mount that I’ve installed in my house, and so far it’s my favorite amongst those three. It’s a well-built, extremely solid and nicely-designed TV mount that perfectly fit my 2013 Sony Bravia 50″ HDTV (a VESA 400×400 pattern).Of the three arm mounts I’ve used, this one is of particular note because it has a very fluid movement when extended. Other mounts I’ve used have been a little stiff, or the arms are short enough that they are hard to position. While all of them are adjustable by allen wrench, this one comes out of the box with the perfect fluidity to make it a perfect mount for areas where you want to be able to move the TV frequently. The tilt mechanism is amongst the easiest I’ve used and easily sets in place with a pair of set screws.Installation is relatively easy and the instructions that come with this are easy to follow. I mounted the plate with the four wings attached to the back of the TV, and then I installed the arm onto the plate so I could lift it to the wall to get an idea of height for mounting. I then removed the arm, positioned it on the wall and marked drill holes. I drilled pilot holes and installed the supplied lag bolts (which are nice, seemingly strong and adequately long bolts) to secure the arm to the stud in the wall. Once bolted into the stud, this mount is going nowhere.The only ding I’d put against this mount is the way it attaches the plate to the arm. It is a wide lip that sits over a groove in the top of the arm, after which you have to screw in two bolts to secure the plate to the arm. The other two mounts I have utilize a permanently installed screw on the top that you slide into a slot and secure, along with another permanently installed screw on the bottom that you feed into a slot and secure. It is a little more difficult to know you’ve caught the TV onto the arm with this design, and having to find two screw holes by hand behind the TV is a little more difficult than just lining up a nut on the already installed screw of these other mounts. Not a dealbreaker, but a noticeable difference that made the installation finish a little trickier than my past experiences, especially in a case like mine where you’re installing this mount in a recess between shelving units.This unit comes with plenty of hardware in the box, including four lag bolts, plenty of screws for all size TVs, washers, spacers and practically everything else you need — all packed in separated, letter-labelled pouches that correspond to the instruction manual. Easy peasy. It also comes with a cheap but small, real level. Not a tiny little useless one like the other mounts I’ve used, but a real bubble level (about 6-8 inches long) that I can now stick in my toolbox and use elsewhere. Nice perk. There is also an HDMI cable (not sure the length, as I didn’t use it because I had a 15′ existing cable in my wall chase to the receiver) and a small pack of velcro cable ties. Overall a well thought-out package that’s a great value compared to other commercially-available mounts from the likes of Sanus. I didn’t need to orient my mounting plate unconventionally because my mount was pretty standard, but I like that you have the option for a lot of non-standard hole patterns with this mount. I’ve seen pictures where the bottom wings were mounted so you could hang a soundbar. This design just seems like someone was thinking about how to make a mount that would fit practically any situation, they built it right and priced it competitively. I wouldn’t hesitate to recommend this to others.

Excellent and surprisingly affordable
I’ve hung several different TV mounts in the last couple of years. I’m by no means an expert but I know the features that I like. This mount has all of them.The articulating arm mounts to the wall first. The wall plate is well thought out– install the upper and lower screw but leave them loose. The lower mounting hole is slotted so you can adjust the plate to be level, then tighten the whole thing down. You can then install the center screw. If you lag the arm into a wall stud like I did, you can practically hang an engine on it.Install the mounting plate on the TV, then hang the TV on the end of the arm. The mounting plate slots onto the end of the arm and can hang there freely while you tighten the mounting screws. This is a nice touch– another mount that I recently used required a screw to be installed while you held the TV in place, which is hard to do by yourself. Yep, I almost dropped it. This mount avoids that particular problem.After the TV is hung and bolted down, you can adjust the tilt and level. Again, this is pretty straightforward to do. Every adjustment on the arm is well thought-out and easy to perform.This is the best mount I’ve used so far. What’s even better is that the price as of this writing ($29ish) is on par with other mounts that are less sturdy and aren’t as easy to mount or adjust. I should know, I’ve bought a few (unfortunately).Next time I need to hang a TV (it’s only a matter of time– I’m a magnet for “favors”), I’ll be buying this one again.

Does exactly what I needed. Light weight amd strong. Functional and very simple to install.Fits TCL 50inch Google TV.

Vem com todas as ferramentas necessárias para a instalação. Qualidade impecável.

This is a good quality mount best suited for offices but if you’re not constantly adjusting the tilt (must be unlocked, relocked with allen key) and extension (swinging jointed arm, not spring) it’s fine for home use. Instructions are clear and simple, includes huge variety of screws and washers as well as plate-arms to accomidate all the form factors I know of. It just seems solidly engineered. DON’T DO THIS UNLESS… But: I was forced to mount this on 3 horizonal studs spanning 6″ instead of the 1 verticle stud it is designed for using only 2/3 bolts but as my TV is only 1/3 of the maximum weight I decided to go ahead and after throughly weight testing I went ahead with mounting without issue (though I later added a little extra security with drywall anchored screws in the remaining slot). Again, I do not recommed this and it will void the manufacturer’s warrantly, but it is engineered well enough to push the stated design limits. All tools needed are included, though I would recommend an actual torque wrench and stud finder.